abaqus隱式求解報的這個錯誤怎么解決呀？
各位大佬，在ABAQUS仿真中，我用了隱式動力學提交job的時候報了這兩個錯A material property that is not allowed with a user material has been specifiedAnalysis Input File Processor exited with an error.
2795 2 4
&SANK ??? 3年前
文獻速覽第4期-隔熱保溫氣凝膠材料 
Further optimization based on bioinspired design and material efficiency improvement has been adopted as effective approaches to achieve satisfactory performance.
4149
熱管理博覽會 ??? 2年前
熱界面材料（TIM）近期熱文速覽 
It can keep mechanical stability after 10,000 cycles at a compressive strain of 60% and sustain high temperature up to 500 °C, which has never been realized in previous reports.
2293
熱管理博覽會 ??? 2年前
Abaqus自帶RSG插件實例 
"IntProp-1" has been created.
3729 3 1
360克 ??? 2年前
Moldex3D仿真分析之Hot Runner System 
Hot runner technology has been the solutions to these issues on many plastic products.
1073
Moldex3D 中國 ??? 2月前
Moldex3D模流分析之Process Characteristics 
Hot runner technology has been the solutions to these issues on many plastic products.
2188
Moldex3D 中國 ??? 1年前
2025大賽優秀作品 | 基于Ansys的XDFOI晶圓級封裝工藝的翹曲模擬與實驗驗證 
However, challenges persist in defining realistic material properties for underfill resins and encapsulants.
1343
Ansys中國 ??? 2月前
Moldex3D模流分析之Characteristics 
Hot runner technology has been the solutions to these issues on many plastic products.
2305
Moldex3D 中國 ??? 1年前
abaqus分析熱軋橢圓空心型鋼的抗壓強度（一） 
</p><p>Replication of test results has been found to be satisfactory with the numerical models able to successfully capture the observed stiffness, ultimate load, general load–end shortening response and
2663
abaquser ??? 1年前
ansys計算發生了錯誤，應該怎么修改？
This may be caused by a bad temperature-dependent material property used in the model.
2172 1
S_2240 ??? 3年前
TCL自學筆記-02
The Mask panel has been pushed using the command "hm_pushpanel mask". A mark of loads is created in the Mask panel.
2256 2
CAE追夢者 ??? 3年前
abaqus報錯
The strain at failure must be greater than zero *density requires the use of *user material, *elastic, *eos, *hyperelastic, *anisotropic hyperelastic, *hyperfoam, *low density foam or *fabric
2606 1
用戶_43019 ??? 2年前
Moldex3D模流分析之Design of experiment, DOE 
Design of experiment, DOEThe final quality of injection molded products is related to multiple factors such as product design, mold design, material properties, and molding conditions; changes in each
2538
Moldex3D 中國 ??? 1年前
三十四、Fluent液體噴霧蒸發模擬 
計算設置 Time Step Method 設置為User-Specified 用戶自定義，偽時間步長Pseudo Time Step Size設置為1s，迭代次數設置為150步 10. 后處理 10.1 新建剪切面Results → Surface → Create → Iso-Surface...
3639 1 1
Fluent學習筆記 ??? 2年前
汽車前沿技術 | NVH前沿工程技術 
The bushings’ special material properties give the required stiffness levels while also damping both radial and axial excitations generated by the compressor.
3848 3
聲學工程師小吳 ??? 2年前
Moldex3D模流分析之To effectively find the key factors 
Design of experiment, DOEThe final quality of injection molded products is related to multiple factors such as product design, mold design, material properties, and molding conditions; changes in each
2513
Moldex3D 中國 ??? 1年前
ABAQUS中Cohesive模型粘聚力模型的2種定義方式 
圖4 第四步：Cohesive單元截面屬性，在Property模塊中，點擊create section，在彈出的界面中選擇，選擇Other->Cohesive，Material選擇剛才定義的cohesive材料，Response選擇Traction Separation， Initial Thickness可使用默認值，也可指定。
6891 28 7
jiaoyou3385 ??? 3年前
Moldex3D模流分析之Find the Optimal Solutions Combining DOE and Molding Simulation 
Design of experiment, DOEThe final quality of injection molded products is related to multiple factors such as product design, mold design, material properties, and molding conditions; changes in each
2346 1
Moldex3D 中國 ??? 1年前
Lsdyna出現“Initialization completed”后就沒有了，沒有error沒有termination
expanding memory to 2879 d 1549004 material properties expanding memory to 2885 d 240737885 element data for composite material expanding memory to 2899 d
2674 2
明月照我程 ??? 2年前
20條/頁 
跳至頁
技術鄰APP
工程師必備
工程師必備
- 項目客服
- 培訓客服
- 平臺客服
TOP
